Plan to Build A Deck
Once you have a solid set of audio instructions and work plans of bridges, construction of a dwelling should not be a difficult process, even for an experienced carpenter.
The technique explained in this paper a method of indoor work that can be used for platform heights of 350 mm to 1.8 m above ground level.
Insert wooden posts
1. Develop the plan cover paper. (If you’re stuck for ideas, there are many online resources covering procurement plans) To fully develop the design of the cover will know exactly where to place their messages and their structure of posts and beams .
2. Place the perimeter of the roof with a rope or line. If you build a square platform, be sure to check the diagonal measurements.
3. Mark the positions of their messages with a pen or chalk. Your messages should be about 1.5 to 1.8 meters.
4. Now, dig holes in his messages are about 400 mm deep. Insert your message in the holes, alignment and bracing, to ensure that the reinforcements are held in place while concrete sets. The message below will be reduced so that no matter how high that extend from the floor.
5. Make sure that your posts are plumb (level in the vertical plane.)
6. Pour a little concrete fact and in the holes, filling up.
7. Let the concrete set for 48 hours before removing the backing wood and concrete cleaning all positions.
Correa Stage
Belts are horizontal beams along the length of your platform to support the decking boards. The belts are supported throughout their length messages.
The belt structure will run the same direction as the finished floor, which is generally parallel to the house doors or patio.
Decide what level you want your platform has proven to be, then calculate its height after that – back to FIG.
Use the self-leveling laser level on a tripod to set the levels on a large terrace. Make sure that any level laser is used has been calibrated within the last 6 months.
Bolt 6 “x 2″ boards on edge of each side of the posts, beams staggered so that not end up with two cards in the same position. (Locks of wood can be used in place of the screw, because they are so strong and much faster to use. Pre-drilled 6 “x 2″ insert wood first, at least two wood screws or ties.
As reinforcement insert additional 4 “x 2″ leg between the dwarf 6 “x 2″ and the concrete base and attach to the post with wood screws or fasteners. This will ensure that your sub will last over 20 years. This will transfer the load to the ground.
Let the water run-off
To create a runoff must create a slight slope to the terrace. We will point to a slope of about 1 in 100. To do this, we will establish our levels of use of the line manufacturers. 50 mm 4.8 million will create a slope of 1 in 100.
dwarf legs can be used to reinforce straps. Once the straps are placed and screwed / timberlocked belt structure is complete.
joists Stage
On the basis of the beams is ahead right now (make sure the beams 4 “x 2″ (or 5 6 “x 2″) are regularized (the beams are actually the same size) – this is very If not important, the platform could be uneven.)
Put your high beams of the belt at 90 ° to the belt structure. Joists must be placed at 250 mm (10 inches). The beams can be attached to the structure of straps with stainless steel screws, 80 mm or 3 nails galvinised. This should ensure the soundness and sustainability of its platform the past two decades of use.
Now all that remains is to insert the bridge components between beams to strengthen the structure of beams. The use of 10 “(250mm) pieces for this.
Reduction of 250 mm pieces (10 “) must be inserted between the joists to provide a rigid structure, powerful beam.
Incoming search terms:
- deck plans
- decking designs
- deck design ideas
- plans for deck
- ground level deck ideas
- covered deck designs pictures
- powered by phpBB art gallery lighting
- build a ground deck
- covered deck design ideas
- above ground deck plans
No related posts.
Discussion Area - Leave a Comment